Porter-Cable 121 6 Amp Hand Held Oscillating Spindle Sander
Cheapest Deal Milwaukee 6020-21 1/4-Sheet Orbital Sander, Serious I.
Serious Issues With The Clamps Limit An Otherwise Useful Tool, QUICK TAKE: The mounting clamps incorrect - it is difficult to insert the card, and the front clip losing its grip for some time. Thus, many users will find this tool is wasting a lot of time.
Even for those who use self-adhesive sandpaper, or use the light or casual, this tool is a good value at current prices heavily discounted. The effect gives rapid results and an elegant finish.
Two problems with terminals: There are two big problems with pliers to hold sandpaper. Because this is where the rubber meets the road, so to speak, will be serious problems for many users:
1 - The terminals are very embarrassing for the installation of paper - it has to force the clip open and mess with getting the edge of the wound pad and clamp. A lever on the swings, and you must use the lever to lift the clamp just enough to make paper. It takes a long time 'strength to open the terminal, even if the handle is not as useful.
Milwaukee 6020-21 1/4-Sheet Orbital Sander ,Reviewed by snapcrackle (United States)
Satisfied Rating (6/10)
Related Reviews
Cheap OSCILLATING SANDER for Sale (Top 10)
|
Top #1 JET 708404 JBOS-5 5-1/2 Inch 1/2 Horsepower Benchtop Oscillating SpindleOverall Rating (8/10) |
|
| Review by A. Heady (Honeydew, CA) 2008-09-12 Received the Sander in great condition, however the quality control at the factory is poor. The table was not square to the spindle. I did some checking and found the table mounting brackets were not drilled and tapped at the same height. I ordered replacement brackets and they were the same as the originals. I fixed it buy installing some bras... Read more JET 708404 JBOS-5 reviews | ||
|
Top #2 JET 708447 OES-80CS 6-Inch 1-1/2-Horsepower Oscillating Edge Sander, 115/230-Volt 1-PhaseOverall Rating (6/10) |
|
| Review by W. Ramirez (Northern Virginia) 2008-03-10 the tool itself is fine and works as advertised, but I am not pleased with Amazon. First of all, the carton did not have any outside damage which was why accepted the package in the first place. Upon opening it to begin to set it up it was very obvious that something was wrong. Many of the metal parts were bent considerably and the dry ice separato... Read more JET 708447 OES-80CS reviews | ||
|
Top #3 Grizzly G0538 1/3 HP Oscillating Spindle SanderOverall Rating (8/10) |
|
| Review by Barbara Roberts (USA) 2009-02-27 This is just what we want. Works great, Fast shipping, Thank you so much. Barbara... Read more Grizzly G0538 1/3 reviews | ||
|
Top #4 Triton TC450SPS 3.5 amp Oscillating Spindle SanderOverall Rating (8/10) |
|
| Review by helpful joe (point venture, tx United States) 2008-11-09 No reviews here at this time so here is my non-expert opinion. I just got this triton sander from Amazon and everthing was in order. Setup is easy and it works well for my usage, cleaning up curves cut in 3/4" plywood and hardwood. Construction is solid and there is minimal vibration. I will say I found it tricky at first to freehand sand to the... Read more Triton TC450SPS 3.5 reviews | ||
|
Top #5 Porter-Cable 121 6 Amp Hand Held Oscillating Spindle SanderOverall Rating (8/10) |
|
| Review by Martin Maher (Oceanside, New York United States) 2007-12-11 Delta 31-781 Sanding Spindle Set for 31-780 B.O.S.S. Spindle Sander This sander comes with one 2" diameter spindle. If you need other sizes you must buy them (follow link above) . This spindle set is for the Delta BOSS but it fits the PC sander as well .The set includes some some table inserts and a couple of plastic parts holders. $65 is t... Read more Porter-Cable 121 6 reviews | ||
|
Top #6 Genesis GMT15A Multifunction Oscillating ToolOverall Rating (8/10) |
|
| Review by Pete from Boston (MA United States) 2010-07-20 The tool never worked, wouldn't power on. Sent item back to Amazon and went to Home Depot and purchased a Dremel saw.... Read more Genesis GMT15A Multifunction reviews | ||
|
Top #7 Fein MultiMaster 250 Start Power Sanding and Scraping/Cutting ToolOverall Rating (8/10) |
|
| Review by Steve Larson (Christmas, Florida) 2010-07-25 This is a very nice tool. I needed to cut the bottoms off 7 door jambs to accommodate wood flooring. It is the perfect tool for that part of a project. It came highly reccommended by a friend who had tried the Dremmel & Pockwell versions, and it didn't disappoint.... Read more Fein MultiMaster 250 reviews | ||
|
Top #8 Rockwell RK9011 Oscillating Spindle SanderOverall Rating (10/10) |
|
| Review by Wask (San Francisco) 2010-01-11 Received this product with free shipping from Fed Ex in great condition. The instructions are a little vague, but not really an issue being that it is simple to set up. The cast iron table is about an 1/8th of an inch thick and is tightly ribbed underneath. The plastic housing seems typical; I will have to check back later to see how ... Read more Rockwell RK9011 Oscillating reviews | ||
